cmm BRIDGE | kronos

• Moving alloy bridge frame on granite table machine base with isostatic supporting system
• Z ram made of micro-machined alloy extrusion or Silicon Carbide (NT)
• Mixed rack and pinion drives with zero-hysteresis friction drive for smooth and repeatable operations
• Measuring system with high-resolution linear transducers (0.1 μm)
• Multi-sensor temperature compensation system complete with part temperature probe

• Temperature range for metrological specification:
  – T1:
  Ambient temperature: 18 ÷ 22 °C
  Maximum hourly gradient: 1,0 °C/h
  Maximum daily gradient: 2,0 °C/24h
  Maximum volume gradient: 0,5 °C/m
  – T2:
  Ambient temperature: 16 ÷ 26 °C
  Maximum hourly gradient: 1,0 °C/h
  Maximum daily gradient: 5,0 °C/24h
  Maximum volume gradient: 1,0 °C/m
• Operating temperature: 15 ÷ 35 °C
• Operating relative humidity: 40 ÷ 80 % (non-condensing)
• Allowed vibrations: (Acceleration between peaks)
  30 mm/s²tra 1 e 10 Hz
  15 mm/s² tra 10 e 20 Hz
  50 mm/s² tra 20 e 100 Hz

• Minimum air supply: 6 Bar -79PSI
• Air consumption: 160Nl/min
• Power supply voltage: 230 V ± 10%; 50 Hz ± 2% single-phase
• Maximum power consumption: 10A 1600W

• Manual probe heads: MIH, MH20, MH20i
• Motorised indexable probe heads: PH10T, PH10M, PH10MQ
• Point to point trigger probes: TP2, TP20, TP200
• Analogue contact probes: Analogue scanning contact probe SP25
• | Laser probes: Metris LC/XC series (qualification sphere included)
• Stylus and probe changers: fully automatic changing stations

All Coord3 CMM products are factory-tested for accuracy according to the UNI EN ISO 10360 – 2 standard

KRONOS NT 20.15

The services indicated are valid under the following conditions: 
– PH10M/PH10MQ/PH20/TP20/TP200: Ø4mm stylus length 10mm
– PH10MQ/SP25: SM1, stylus Ø 5mm x 50mm
– L= measuring length in mm
– Ambient temperature conditions: 
T_{1 :} 18÷22 °C; Degrees max: 1,0 °C/h – 2,0 °C/24h – 0,5 °C/m
T₂: 16÷26°C; Degrees max: 1,0 °C/h – 5,0 °C/24h – 1,0 °C/m

^[1] Maximum Permissible Error on length measurements according to ISO 10360-2
^[2] Maximum permissible point gripping error according to ISO 10360-2
^[3] Maximum Permissible Error of scanning point gripping according to ISO 10360-4 standard for SP25M / SP80 probes

KRONOS NT 13.10 – 15.13

Le prestazioni indicate sono valide nelle seguenti condizioni: 
– PH10M/PH10MQ/PH20/TP20/TP200: Ø4mm lunghezza stilo 10mm
– PH10MQ/SP25: SM1, stilo Ø 5mm x 50mm
– L= lunghezza di misura in mm
– Condizioni di temperatura ambientale: 
T_{1 :} 18÷22 °C; Gradienti max: 1,0 °C/h – 2,0 °C/24h – 0,5 °C/m
T₂: 16÷26°C; Gradienti max: 1,0 °C/h – 5,0 °C/24h – 1,0 °C/m

^[1] Massimo Errore Permissibile su misure di lunghezza secondo la norma ISO 10360-2
^[2] Massimo Errore Permissibile di presa punto secondo la norma ISO 10360-2
^[3] Massimo Errore Permissibile di presa punto in scansione secondo la norma ISO 10360-4 per tastatori SP25M/SP80

• Passive vibration isolation system
• Active vibration isolation system (AVM)
• Multi-wire cables
• Pallet loading/unloading system,  manual or automatic
• PC and printer
• Training c/o Coord3 Centres or resellers
• Installation by Coord3 personnel or resellers
• Models and sizes:
  COORD3 KRONOS CMMs are available with the following measuring strokes (Y.Z mm):
  13.10/15.13/20.15